How To Replace Led Light In Whirlpool Refrigerator?

How to Replace a LED Light in a Whirlpool Refrigerator

Your Whirlpool refrigerator is an essential appliance in your kitchen, and it’s important to keep it in good working order. One of the most common problems with refrigerators is a burned-out LED light. Fortunately, replacing a LED light in a Whirlpool refrigerator is a relatively simple task that you can do yourself.

In this article, we’ll walk you through the steps of replacing a LED light in a Whirlpool refrigerator. We’ll provide detailed instructions and images to help you get the job done quickly and easily.

So if your refrigerator light is out, don’t despair. Just follow these steps, and you’ll be back to enjoying your cold drinks and frozen foods in no time.

Step Instructions Image
1 Unplug the refrigerator from the power outlet.
2 Remove the screws that hold the light cover in place.
3 Pull the light cover off of the refrigerator.
4 Disconnect the wires from the old light bulb.
5 Insert the new light bulb into the socket.
6 Reconnect the wires to the new light bulb.
7 Replace the light cover.
8 Plug the refrigerator back into the power outlet.

Tools and Materials Needed

To replace the LED light in your Whirlpool refrigerator, you will need the following tools and materials:

  • A Phillips head screwdriver
  • A replacement LED light kit
  • A tape measure
  • A flashlight

Steps to Replace the LED Light

1. Turn off the power to the refrigerator. This is important to do before you begin any work on the refrigerator, as you do not want to accidentally electrocute yourself. To turn off the power, locate the circuit breaker panel in your home and find the breaker that controls the refrigerator. Flip the breaker to the “Off” position.
2. Locate the LED light. The LED light is located on the inside of the refrigerator, near the top. It is a small, rectangular light that is typically white or blue.
3. Remove the cover of the LED light. The cover is held in place by a few screws. Use the Phillips head screwdriver to remove the screws and then carefully remove the cover.
4. Disconnect the wiring harness. The wiring harness is a small, black cable that connects the LED light to the refrigerator’s circuit board. Use the Phillips head screwdriver to disconnect the wiring harness.
5. Install the new LED light. The new LED light should come with a set of instructions. Follow the instructions to install the new LED light.
6. Reconnect the wiring harness. Once the new LED light is installed, reconnect the wiring harness.
7. Replace the cover of the LED light. Replace the cover of the LED light and then secure it in place with the screws.
8. Turn on the power to the refrigerator. Flip the breaker to the “On” position to turn the power back on to the refrigerator.

Replacing the LED light in your Whirlpool refrigerator is a relatively simple task that can be completed in a few minutes. By following the steps in this guide, you can have your refrigerator back up and running in no time.

Here are some additional tips for replacing the LED light in your Whirlpool refrigerator:

  • If you are not comfortable working on electrical appliances, it is best to hire a qualified electrician to do the job for you.
  • Make sure that the replacement LED light is the correct size and type for your refrigerator.
  • Be careful not to damage the wiring harness when you are disconnecting and reconnecting it.
  • Test the LED light to make sure that it is working properly before you replace the cover.

3. Unplug the refrigerator from the power outlet.

Before you begin any repairs on your refrigerator, it is important to unplug it from the power outlet. This will help to prevent any electrical shocks.

To unplug your refrigerator, locate the power cord at the back of the unit. The power cord is typically black and has a three-pronged plug. Grasp the plug firmly and pull it straight out of the outlet.

Once the refrigerator is unplugged, you can begin to remove the kickplate.

4. Remove the kickplate from the bottom of the refrigerator.

The kickplate is a plastic panel that covers the bottom of the refrigerator. It is typically held in place by a series of clips.

To remove the kickplate, locate the clips along the bottom edge of the panel. Using a flathead screwdriver, carefully pry up the clips one at a time. Once all of the clips are removed, you can lift up the kickplate and remove it from the refrigerator.

Tips for removing the kickplate

  • Be careful not to damage the kickplate when removing it.
  • If the clips are difficult to pry up, you can use a hairdryer to heat them up. This will make them more pliable and easier to remove.
  • Once the kickplate is removed, you can set it aside in a safe place.

Replacing the LED light

Once the kickplate is removed, you can access the LED light. The LED light is typically located in the center of the refrigerator. It is held in place by a series of clips.

To remove the LED light, locate the clips along the sides of the light. Using a flathead screwdriver, carefully pry up the clips one at a time. Once all of the clips are removed, you can lift up the LED light and remove it from the refrigerator.

Tips for replacing the LED light

  • Be careful not to damage the LED light when removing it.
  • If the clips are difficult to pry up, you can use a hairdryer to heat them up. This will make them more pliable and easier to remove.
  • Once the LED light is removed, you can install the new light.

Installing the new LED light

To install the new LED light, simply reverse the steps you took to remove the old light.

First, insert the new light into the housing. Then, secure the light in place with the clips. Finally, replace the kickplate.

Tips for installing the new LED light

  • Make sure that the new light is the correct size and type for your refrigerator.
  • Be careful not to damage the new light when installing it.
  • Once the new light is installed, you can plug the refrigerator back into the power outlet.

Replacing the LED light in your Whirlpool refrigerator is a relatively simple task. By following these steps, you can have your refrigerator back up and running in no time.

Additional tips

  • If you are not comfortable working on your refrigerator, you can always hire a qualified technician to do the job for you.
  • When shopping for a new LED light, make sure to choose a light that is the correct size and type for your refrigerator.
  • Be sure to dispose of the old LED light properly.

    How do I know if my Whirlpool refrigerator’s LED light needs to be replaced?

  • The light is not working.
  • The light is flickering.
  • The light is dim.

How do I remove the old LED light?

1. Turn off the power to the refrigerator.
2. Remove the screws that hold the light cover in place.
3. Pull the light cover off of the refrigerator.
4. Remove the old LED light by disconnecting the electrical connector and pulling it out of the housing.

How do I install the new LED light?

1. Align the new LED light with the housing.
2. Insert the electrical connector into the housing.
3. Secure the light cover in place with the screws.
4. Turn on the power to the refrigerator.

What type of LED light do I need for my Whirlpool refrigerator?

You will need a Whirlpool LED light that is the same size and shape as the old light. You can find the correct replacement light by looking at the model number of your refrigerator.

How much does it cost to replace an LED light in a Whirlpool refrigerator?

The cost of replacing an LED light in a Whirlpool refrigerator varies depending on the model of refrigerator. The average cost is between $10 and $20.

Can I replace the LED light in my Whirlpool refrigerator myself?

Yes, you can replace the LED light in your Whirlpool refrigerator yourself. However, if you are not comfortable working with electrical components, it is best to have a qualified technician do the replacement for you.

In this blog post, we have discussed how to replace the LED light in a Whirlpool refrigerator. We have provided step-by-step instructions, as well as pictures and videos to help you along the way. We hope that this information has been helpful and that you are now able to replace the LED light in your refrigerator with ease.

Here are the key takeaways from this blog post:

  • The LED light in a Whirlpool refrigerator is located behind the refrigerator’s ice maker.
  • To replace the LED light, you will need to remove the ice maker and the cover plate behind it.
  • The new LED light is a simple plug-and-play replacement.
  • Replacing the LED light is a relatively easy task that can be completed in about 15 minutes.

We hope that this blog post has been helpful. If you have any questions, please leave them in the comments below.

Author Profile

Design By Typing
Design By Typing
We’ve turned typing into an art form. We don’t just scratch the surface; we type through it, breaking the crust of the conventional and bringing to light the layers of knowledge beneath. Our words are our paint, our keyboards the canvas, and the result? A masterpiece of information that’s as accurate as it is compelling.

We’re a band of inquisitive souls, data detectives, and prose pros. We’re not your average joe with a search engine. We dig deeper, leap further, and stay up way too late for the sake of quenching the knowledge thirst. Our team is a motley crew of expert researchers, savvy writers, and passionate nerds who believe that the right answer isn’t always the first one Google spits out.

Similar Posts