How To Bypass Door Switch On Dryer?

How to Bypass a Dryer Door Switch

Your dryer door switch is a critical safety feature that prevents the dryer from operating when the door is open. However, if your dryer door switch malfunctions, you may need to bypass it in order to use your dryer. Bypass the door switch is a relatively simple process, but it is important to follow the steps carefully to avoid damaging your dryer.

In this article, we will walk you through the process of bypassing a dryer door switch. We will provide step-by-step instructions and safety tips, so you can safely and effectively get your dryer back up and running.

Step	Action	Explanation
1	Unplug the dryer from the wall outlet.	This will prevent the dryer from running while you are working on it.
2	Locate the door switch on the dryer.	The door switch is usually located near the door of the dryer. It is a small, rectangular switch with two terminals.
3	Disconnect the wires from the door switch.	Use a screwdriver to disconnect the wires from the door switch. Be careful not to damage the wires.
4	Bypass the door switch.	You can bypass the door switch by connecting the two wires together. You can do this by using a piece of wire or a paperclip.
5	Plug the dryer back into the wall outlet.	The dryer should now be able to operate without the door switch.

How To Bypass Door Switch On Dryer?

Identifying the Door Switch

The door switch is a safety device that prevents the dryer from operating when the door is open. It is typically located on the inside of the dryer door, near the top. The door switch is a small, rectangular device with two terminals. When the door is closed, the switch closes the circuit between the two terminals, allowing the dryer to operate. When the door is open, the switch opens the circuit, preventing the dryer from operating.

Bypass the Door Switch

There are a few different ways to bypass the door switch on a dryer. The best method for you will depend on the type of dryer you have and your level of comfort with DIY projects.

Method 1: Use a jumper wire

This is the simplest way to bypass the door switch. To do this, you will need a jumper wire (a piece of wire with two bare ends) and a pair of pliers.

1. Turn off the dryer and unplug it from the outlet.
2. Open the dryer door and locate the door switch.
3. Use the pliers to disconnect the two wires from the door switch.
4. Connect the jumper wire between the two terminals of the door switch.
5. Close the dryer door.
6. Plug the dryer back into the outlet and turn it on.

The dryer should now operate normally, even with the door open.

Method 2: Use a switch bypass kit

A switch bypass kit is a pre-assembled device that allows you to bypass the door switch without having to do any wiring yourself. To use a switch bypass kit, simply follow the instructions that come with the kit.

Method 3: Rewire the door switch

This is the most involved way to bypass the door switch, but it also provides the most flexibility. To rewire the door switch, you will need to remove the door switch from the dryer and then rewire it so that it bypasses the safety mechanism.

1. Turn off the dryer and unplug it from the outlet.
2. Open the dryer door and locate the door switch.
3. Remove the screws that hold the door switch in place.
4. Carefully remove the door switch from the dryer.
5. Disconnect the two wires from the door switch.
6. Strip the ends of the wires.
7. Connect the wires to a new switch in the same way that they were connected to the old switch.
8. Reinstall the door switch in the dryer.
9. Plug the dryer back into the outlet and turn it on.

The dryer should now operate normally, even with the door open.

Bypassing the door switch on a dryer is a relatively simple process, but it is important to follow the instructions carefully to avoid damaging the dryer. If you are not comfortable with DIY projects, it is best to have a qualified technician bypass the door switch for you.

Additional tips

• If you are bypassing the door switch to prevent the dryer from running when the door is open, be sure to keep the door closed when the dryer is in use.
• If you are bypassing the door switch to troubleshoot a problem with the dryer, be sure to restore the door switch to its original function once the problem has been resolved.

3. Testing the Door Switch

How to test the door switch to make sure it is working properly?

The door switch on a dryer is a safety device that prevents the dryer from operating if the door is open. If the door switch is not working properly, the dryer may not start or may stop working mid-cycle.

There are a few different ways to test the door switch to make sure it is working properly.

• Visual inspection

The first step is to visually inspect the door switch. Look for any damage to the switch itself, as well as the wiring that connects the switch to the dryer. If you see any damage, the switch will need to be replaced.

• Test with a multimeter

Another way to test the door switch is to use a multimeter. A multimeter is a tool that can measure electrical current, voltage, and resistance. To test the door switch with a multimeter, follow these steps:

1. Turn off the dryer and unplug it from the wall outlet.
2. Set the multimeter to the resistance setting.
3. Touch the red probe of the multimeter to the “COM” terminal on the multimeter.
4. Touch the black probe of the multimeter to the “NO” terminal on the door switch.
5. Close the dryer door.
6. The multimeter should read “0” ohms.
7. Open the dryer door.
8. The multimeter should read “infinity” ohms.

If the multimeter reads “0” ohms when the door is closed and “infinity” ohms when the door is open, the door switch is working properly. If the multimeter reads anything other than “0” ohms when the door is closed or “infinity” ohms when the door is open, the door switch needs to be replaced.

• Test with a jumper wire

Another way to test the door switch is to use a jumper wire. A jumper wire is a short piece of wire that can be used to connect two points in a circuit. To test the door switch with a jumper wire, follow these steps:

1. Turn off the dryer and unplug it from the wall outlet.
2. Remove the access panel on the back of the dryer.
3. Locate the door switch.
4. Connect one end of the jumper wire to the “COM” terminal on the door switch.
5. Connect the other end of the jumper wire to the “NO” terminal on the door switch.
6. Close the dryer door.
7. The dryer should start.
8. Open the dryer door.
9. The dryer should stop.

If the dryer starts and stops when you close and open the door, the door switch is working properly. If the dryer does not start or stop, the door switch needs to be replaced.

3. What are the different ways to test the door switch?

There are three different ways to test the door switch on a dryer:

• Visual inspection
• Multimeter
• Jumper wire

Visual inspection is the simplest way to test the door switch. Simply look for any damage to the switch itself, as well as the wiring that connects the switch to the dryer. If you see any damage, the switch will need to be replaced.

A multimeter is a tool that can measure electrical current, voltage, and resistance. To test the door switch with a multimeter, follow these steps:

1. Turn off the dryer and unplug it from the wall outlet.
2. Set the multimeter to the resistance setting.
3. Touch the red probe of the multimeter to the “COM” terminal on the multimeter.
4. Touch the black probe of the multimeter to the “NO” terminal on the door switch.
5. Close the dryer door.
6. The multimeter should read “0” ohms.
7. Open the dryer door.
8. The multimeter should read “infinity” ohms.

If the multimeter reads “0” ohms when the door is closed and “infinity” ohms when the door is open, the door switch is working properly. If the multimeter reads anything other than “0” ohms when the door is closed or “infinity” ohms when the door is open, the door switch needs to be replaced.

A jumper wire is a short piece of wire that can be used to connect two points in a circuit. To test the door switch with a jumper wire, follow these steps:

1. Turn off the dryer and unplug it from the wall outlet.
2. Remove the access panel on the back of the dryer.
3. Locate the door switch.
4. Connect one end of the jumper wire to the “COM” terminal on the door switch.
5. Connect the other end of the jumper wire to the “NO” terminal on the door switch.
6.

How do I bypass the door switch on my dryer?

There are a few ways to bypass the door switch on your dryer. Here are two of the most common methods:

1. Use a coin.

• Turn off the dryer and unplug it from the outlet.
• Locate the door switch on the back of the dryer. It will be a small, rectangular switch with two terminals.
• Insert a coin into the slot on the switch and turn it clockwise. This will bypass the switch and allow you to open the dryer door.
• Be careful not to damage the switch.
• Once you have opened the dryer door, you can replace the coin and plug the dryer back in.

2. Use a jumper wire.

• Turn off the dryer and unplug it from the outlet.
• Locate the door switch on the back of the dryer. It will be a small, rectangular switch with two terminals.
• Strip the ends of a jumper wire and connect one end to each of the terminals on the switch.
• This will bypass the switch and allow you to open the dryer door.
• Be careful not to damage the switch.
• Once you have opened the dryer door, you can disconnect the jumper wire and plug the dryer back in.

What are the risks of bypassing the door switch on my dryer?

There are a few risks associated with bypassing the door switch on your dryer. Here are some of the most common:

• Fire hazard. If the dryer door is not closed properly, it can create a fire hazard.
• Electrical shock. If you bypass the door switch incorrectly, you could be electrocuted.
• Damage to your dryer. Bypassing the door switch can damage your dryer.

When should I bypass the door switch on my dryer?

You should only bypass the door switch on your dryer if you are unable to fix the switch itself. If you are not comfortable working with electrical components, you should have a qualified technician repair the switch for you.

How do I fix the door switch on my dryer?

To fix the door switch on your dryer, you will need to:

1. Turn off the dryer and unplug it from the outlet.
2. Locate the door switch on the back of the dryer. It will be a small, rectangular switch with two terminals.
3. Remove the screws that hold the switch in place and carefully remove the switch.
4. Inspect the switch for damage. If the switch is damaged, you will need to replace it.
5. To replace the switch, simply reverse the steps above.

Where can I find a replacement door switch for my dryer?

You can find a replacement door switch for your dryer at most major home improvement stores. You can also order a replacement switch online.

What is the average cost of a replacement door switch for a dryer?

The average cost of a replacement door switch for a dryer is between $10 and $20.

In this blog post, we have discussed how to bypass a dryer door switch. We have provided step-by-step instructions on how to do this safely and effectively. We have also discussed the reasons why you might need to bypass a dryer door switch, as well as the potential risks involved.

We hope that this information has been helpful. If you have any further questions, please do not hesitate to contact us.

Here are some key takeaways from this blog post:

• A dryer door switch is a safety device that prevents the dryer from operating if the door is open.
• There are a few reasons why you might need to bypass a dryer door switch, such as if the switch is broken or if you need to remove the dryer door for cleaning.
• To bypass a dryer door switch, you will need to disconnect the switch from the dryer’s control board.
• Bypass a dryer door switch at your own risk. There is a risk of fire or electric shock if you do not bypass the switch correctly.