How To Cut Blinds That Are Too Wide?

How to Cut Blinds That Are Too Wide

Your blinds are too wide. You’ve tried everything to make them fit, but nothing seems to work. You’re about to give up and buy new blinds when you remember something you read online. You can cut your blinds to size!

This is a great solution if you’re not ready to invest in new blinds or if you just want to save a few bucks. Cutting your blinds is a simple process that anyone can do. In this article, we’ll walk you through the steps, so you can have perfectly fitted blinds in no time.

We’ll start by discussing the tools and materials you’ll need. Then, we’ll show you how to measure your blinds and cut them to size. Finally, we’ll give you some tips on how to install your new blinds.

Step	Tools	Instructions
1	Tape measure	Measure the width of the blinds that you need to cut.
2	Scissors	Cut the blinds to the desired width, making sure to leave a 1/2-inch seam allowance.
3	Iron	Press the seams flat to finish the blinds.

Tools and Materials Needed

To cut blinds that are too wide, you will need the following tools and materials:

• A hacksaw or a jigsaw
• A safety mask
• A pair of safety glasses
• A ruler
• A pencil
• A utility knife
• A piece of scrap wood
• A drill
• A drill bit that is the same diameter as the dowels in your blinds

Measuring Your Blinds

Before you can cut your blinds, you need to measure them to make sure that you are cutting them to the correct size. To do this, you will need to measure the width of your window and the height of your window.

To measure the width of your window, measure from the outside edge of one of the jambs to the outside edge of the other jamb. To measure the height of your window, measure from the top of the window to the bottom of the window.

Once you have measured your window, you need to subtract 1 inch from the width measurement and 1 inch from the height measurement. This will give you the final dimensions of your blinds.

Cutting Your Blinds

Now that you have measured your blinds, you can cut them to size. To do this, you will need to follow these steps:

1. Place the blinds on a piece of scrap wood.
2. Use a hacksaw or a jigsaw to cut the blinds to the desired width.
3. Use a utility knife to cut the blinds to the desired height.
4. Use a drill to drill a hole in each of the dowels in your blinds.
5. Insert the dowels into the holes in your blinds.

Installing Your Blinds

Now that you have cut your blinds, you can install them. To do this, you will need to follow these steps:

1. Remove the old blinds from your window.
2. Measure the width and height of your window.
3. Cut the blinds to size.
4. Install the blinds according to the manufacturer’s instructions.

Cutting blinds that are too wide is a simple process that can be completed in a few minutes. By following the steps in this guide, you can easily cut your blinds to the perfect size for your window.

Cutting Your Blinds

If your blinds are too wide, you can easily cut them to size using a few simple tools.

Materials:

• Tape measure
• Pencil
• Utility knife
• Safety glasses
• Saw (optional)

Steps:

1. Measure the width of your window.
2. Mark the desired width on the blinds with a pencil.
3. Use a utility knife to cut along the marked line.
4. If necessary, use a saw to cut through the metal slats.
5. Be sure to wear safety glasses when using a saw.

Tips:

• Make sure to measure your window carefully before cutting your blinds.
• If you are cutting through metal slats, be sure to use a saw that is sharp enough to cut through the metal.
• Be careful not to cut yourself when using a utility knife or saw.

Troubleshooting:

• If your blinds are not the same width, you can stagger the slats so that they are evenly spaced.
• If your blinds are too short, you can add extensions to them.

Installing Your New Blinds

Once you have cut your blinds to size, you can install them on your window.

Materials:

• Screwdriver
• Drill (optional)
• Wall anchors (optional)

Steps:

1. Remove the old blinds from your window.
2. If necessary, clean the window frame.
3. Mark the location of the holes for the blind brackets.
4. Drill holes in the window frame (if necessary).
5. Insert the wall anchors into the holes (if necessary).
6. Screw the blind brackets to the window frame.
7. Hang the blinds on the brackets.

Tips:

• Make sure to measure the location of the holes carefully before drilling.
• If you are using wall anchors, be sure to use the right size anchors for your wall.
• Be careful not to over-tighten the screws when attaching the blind brackets.

Troubleshooting:

• If your blinds are not level, you can adjust the brackets until they are level.
• If your blinds are not aligned, you can adjust the slats until they are aligned.

Cutting and installing new blinds is a relatively simple task that can be completed in a few hours. By following these steps, you can easily update the look of your windows and improve your home’s appearance.

How do I cut blinds that are too wide?

There are a few ways to cut blinds that are too wide. You can use a hacksaw, a jigsaw, or a miter saw.

To cut blinds with a hacksaw:

1. Measure the width of the blinds that you need to cut.
2. Mark the blinds at the desired width with a pencil.
3. Place the blinds on a work surface and secure them with clamps.
4. Use a hacksaw to cut along the marked lines.
5. Sand the edges of the blinds to smooth them out.

To cut blinds with a jigsaw:

1. Measure the width of the blinds that you need to cut.
2. Mark the blinds at the desired width with a pencil.
3. Place the blinds on a work surface and secure them with clamps.
4. Attach a jigsaw blade to the jigsaw.
5. Turn on the jigsaw and set the speed to a low setting.
6. Slowly cut along the marked lines.
7. Sand the edges of the blinds to smooth them out.

To cut blinds with a miter saw:

1. Measure the width of the blinds that you need to cut.
2. Mark the blinds at the desired width with a pencil.
3. Place the blinds on a miter saw table.
4. Align the blade of the miter saw with the marked lines.
5. Turn on the miter saw and make the cut.
6. Sand the edges of the blinds to smooth them out.

What should I do if my blinds are too short?

If your blinds are too short, you can either add extensions to them or replace them with longer blinds.

To add extensions to your blinds:

1. Measure the length of the extensions that you need.
2. Cut the extensions to the desired length.
3. Attach the extensions to the blinds using a staple gun or screws.

To replace your blinds with longer blinds:

1. Measure the width and length of the new blinds that you need.
2. Purchase the new blinds.
3. Remove the old blinds from the window.
4. Install the new blinds.

What are some tips for cutting blinds?

• Use a sharp blade to avoid fraying the edges of the blinds.
• Make sure that the blinds are secure before you start cutting them.
• Cut slowly and carefully to avoid making mistakes.
• Sand the edges of the blinds to smooth them out.

Can I cut blinds without removing them from the window?

Yes, you can cut blinds without removing them from the window. However, it is more difficult to do this and you are more likely to make mistakes. If you are not comfortable cutting blinds without removing them from the window, it is best to remove them first.

there are a few different ways to cut blinds that are too wide. You can use a hacksaw, a jigsaw, or a miter saw. The best way for you to cut your blinds will depend on the type of blinds you have and the tools you have available.

No matter which method you choose, be sure to take your time and measure carefully. Cutting your blinds too short will make them difficult to operate, and cutting them too long will make them look sloppy.

By following these steps, you can easily cut your blinds to the perfect size for your windows.