How To Replace Water Filter In Viking Refrigerator?

How to Replace the Water Filter in Your Viking Refrigerator

Your Viking refrigerator’s water filter is an important part of keeping your water clean and fresh. It removes impurities like sediment, chlorine, and other contaminants that can make your water taste bad or even harmful. But over time, the filter will become clogged and need to be replaced.

Replacing the water filter in your Viking refrigerator is a simple task that you can do yourself in just a few minutes. In this article, we’ll walk you through the process, step by step.

What You’ll Need

• Replacement water filter for your Viking refrigerator
• Phillips head screwdriver
• Wrench (optional)

Instructions

1. Turn off the power to your refrigerator. This will prevent you from accidentally getting shocked.
2. Locate the water filter housing. The water filter housing is typically located in the back of your refrigerator, near the bottom.
3. Remove the old filter. To remove the old filter, twist it counterclockwise until it comes loose.
4. Insert the new filter. To insert the new filter, twist it clockwise until it is snug.
5. Turn on the power to your refrigerator. Your refrigerator will now be able to filter water again.

Step	Instructions	Image
1	Turn off the water supply to the refrigerator.
2	Locate the water filter housing. It is usually located on the back of the refrigerator, near the bottom.
3	Press down on the release tab and pull the water filter out.
4	Insert the new water filter into the housing.
5	Turn on the water supply to the refrigerator.

Your Viking refrigerator’s water filter helps to remove impurities from your water, such as sediment, chlorine, and other harmful bacteria. It is important to replace the water filter regularly to ensure that you are drinking clean, healthy water. This guide will show you how to replace the water filter in your Viking refrigerator.

Tools and Materials Needed

• Replacement water filter
• Phillips head screwdriver
• Wrench
• Bucket
• Paper towels

Steps to Replace the Water Filter

1. Turn off the water supply to the refrigerator. This is usually located at the back of the refrigerator, near the bottom.
2. Locate the water filter housing. The water filter housing is typically located in the back of the refrigerator, near the top. It is a cylindrical-shaped container with a blue cap.
3. Remove the water filter housing cap. To do this, you will need to use a Phillips head screwdriver to unscrew the cap.
4. Remove the old water filter. The old water filter is a cylindrical-shaped cartridge that is located inside the water filter housing. To remove it, you will need to use a wrench to loosen the nut that secures it in place.
5. Insert the new water filter. The new water filter is a cylindrical-shaped cartridge that is the same size as the old water filter. To insert it, you will need to line up the tabs on the filter with the slots in the water filter housing and then push it down until it is seated securely.
6. Replace the water filter housing cap. To do this, you will need to use a Phillips head screwdriver to screw the cap back on.
7. Turn on the water supply to the refrigerator. This is usually located at the back of the refrigerator, near the bottom.
8. Run a glass of water from the refrigerator dispenser. This will help to flush out any air that may be trapped in the new water filter.

Replacing the water filter in your Viking refrigerator is a simple task that can be completed in just a few minutes. By following these steps, you can ensure that you are drinking clean, healthy water.

Here are some additional tips for maintaining your Viking refrigerator’s water filter:

• Replace the water filter every 6 months or according to the manufacturer’s instructions.
• Clean the water filter housing regularly to prevent the build-up of sediment and bacteria.
• Do not use a water filter that is not designed for your Viking refrigerator.
• If you are unsure how to replace the water filter in your Viking refrigerator, consult your owner’s manual or contact a qualified technician.

How to Replace Water Filter in Viking Refrigerator?

Step 1: Gather your tools and materials

To replace the water filter in your Viking refrigerator, you will need the following tools and materials:

• A new water filter (the correct size for your refrigerator)
• A Phillips head screwdriver
• A bucket or large bowl
• Paper towels

Step 2: Turn off the water supply to the refrigerator

Before you can remove the old water filter, you need to turn off the water supply to the refrigerator. This will prevent water from leaking out of the filter housing when you remove the filter.

To turn off the water supply, locate the water supply valve on the back of the refrigerator. The valve is typically a small, round knob. Turn the valve clockwise to turn off the water supply.

Step 3: Locate the water filter housing on the back of the refrigerator

The water filter housing is located on the back of the refrigerator, near the bottom. It is a small, rectangular compartment with a door.

Open the door of the water filter housing. Inside, you will see the old water filter.

Step 4: Remove the old water filter

To remove the old water filter, grasp the handle on the top of the filter and pull it straight out of the housing.

Discard the old filter.

Step 5: Insert the new water filter

To insert the new water filter, align the tabs on the side of the filter with the slots in the housing. Then, push the filter straight into the housing until it clicks into place.

Close the door of the water filter housing.

Step 6: Turn on the water supply to the refrigerator

Turn the water supply valve on the back of the refrigerator counterclockwise to turn on the water supply.

Step 7: Run the water through the filter

To flush out any debris from the new filter, run the water through the filter for a few minutes.

You can do this by turning on the water dispenser or by filling a glass of water.

That’s it! You have now successfully replaced the water filter in your Viking refrigerator.

By following these steps, you can keep your refrigerator running smoothly and ensure that you have fresh, clean water to drink.

Here are some additional tips for maintaining your Viking refrigerator:

• Clean the water filter regularly, according to the manufacturer’s instructions.
• Defrost the refrigerator regularly to prevent ice buildup.
• Keep the refrigerator door closed as much as possible to prevent warm air from entering.
• Clean the interior of the refrigerator regularly with a mild detergent and water.

  How do I know when to replace my Viking water filter?

Your Viking water filter should be replaced every 6 months or 500 gallons, whichever comes first. You can check the filter’s status by looking at the indicator light on the front of the refrigerator. When the light is flashing, it’s time to replace the filter.

How do I remove the old water filter?

1. Turn off the water supply to the refrigerator.
2. Locate the water filter housing on the back of the refrigerator.
3. Press down on the release tab and pull the filter straight out.

How do I install the new water filter?

1. Rinse the new filter under cold water for 5 seconds.
2. Insert the filter into the housing until it snaps into place.
3. Turn on the water supply to the refrigerator.

What if I accidentally installed the filter upside down?

If you accidentally installed the filter upside down, do not turn on the water supply. Remove the filter and reinstall it correctly.

What happens if I don’t replace my water filter?

If you don’t replace your water filter, your water may become cloudy or taste bad. You may also experience decreased water flow from your refrigerator.

Where can I buy a replacement water filter for my Viking refrigerator?

You can purchase a replacement water filter for your Viking refrigerator at most major retailers. You can also order a filter directly from Viking’s website.

In this guide, we have shown you how to replace the water filter in your Viking refrigerator. We hope that this information has been helpful and that you are now able to do this task yourself.

Here are the key takeaways from this guide:

• The water filter in your Viking refrigerator is located behind the kickplate at the bottom of the refrigerator.
• To replace the filter, you will need to remove the kickplate, unscrew the old filter, and insert the new filter.
• The new filter should be installed with the arrow pointing down.
• You should replace the water filter in your Viking refrigerator every 6 months or 500 gallons of water, whichever comes first.

By following these steps, you can easily and quickly replace the water filter in your Viking refrigerator. This will ensure that you have clean, fresh water to drink and cook with.