How To Restring A Stihl Fsa 57 Weed Eater?

How to Restring a Stihl FSA 57 Weed Eater

Your Stihl FSA 57 weed eater is a powerful tool that can help you keep your yard looking its best. But when the string breaks, it can be a pain to replace. Fortunately, restringing a Stihl FSA 57 weed eater is a relatively simple task that can be completed in just a few minutes.

In this article, we will walk you through the process of restringing your Stihl FSA 57 weed eater. We will provide step-by-step instructions and helpful images, so you can get your weed eater back up and running in no time.

So if your Stihl FSA 57 weed eater’s string is broken, don’t despair! Just follow these simple steps to get it restrung and you’ll be back to enjoying your yard in no time.

Step	Instructions	Image
1	Remove the old string from the weed eater.
2	Measure the new string to the correct length.
3	Thread the new string through the eyelets on the weed eater.
4	Tighten the string until it is taught.

This guide will show you how to restring a Stihl Fsa 57 weed eater. The Stihl Fsa 57 is a popular weed eater that is known for its power and durability. However, like all string trimmers, the Stihl Fsa 57 will eventually need to be restringed.

Restringing a Stihl Fsa 57 is a relatively simple task that can be completed in a few minutes. However, it is important to follow the steps carefully in order to avoid damaging the weed eater.

Gather your materials

Before you begin, you will need to gather the following materials:

• Stihl Fsa 57 Weed Eater
• Replacement string
• Tape measure
• Pliers
• Screwdriver

Remove the old string

The first step is to remove the old string from the weed eater. To do this, follow these steps:

1. Turn off the weed eater and disconnect the spark plug wire.
2. Remove the two screws that hold the string guide in place.
3. Carefully remove the string guide from the weed eater.
4. Pull the old string out of the weed eater.

Install the new string

Now that you have removed the old string, you can install the new string. To do this, follow these steps:

1. Cut a piece of string that is about 2 feet long.
2. Thread the string through the hole in the center of the string guide.
3. Wrap the string around the spool, making sure to keep it tight.
4. Thread the string through the hole in the other side of the string guide.
5. Pull the string taut and tighten the screws that hold the string guide in place.

Test the weed eater

Now that you have installed the new string, it is time to test the weed eater. To do this, turn on the weed eater and let it run for a few seconds. The weed eater should now be able to cut through weeds without any problems.

Restringing a Stihl Fsa 57 weed eater is a relatively simple task that can be completed in a few minutes. By following the steps in this guide, you can easily keep your weed eater in good working order.

Here are some additional tips for restringing a Stihl Fsa 57 weed eater:

• Use a high-quality replacement string. A good-quality string will last longer and will provide better performance.
• Make sure to tighten the screws that hold the string guide in place securely. A loose string guide can cause the string to come off of the spool.
• Test the weed eater before using it. This will ensure that the string is installed correctly and that the weed eater is working properly.

3. Install the new string

To install the new string, you will need:

• Two pieces of .095-inch (2.4-millimeter) nylon trimmer line, each 12 inches (30 centimeters) long
• A pair of needle-nose pliers

1. Cut two pieces of string to the same length.
2. Thread one end of each piece of string through the hole in the weed eater.
3. Feed the strings through the string guide and around the spool.
4. Tie the ends of the strings together in a knot.

The knot should be located on the inside of the weed eater, so that it will not interfere with the operation of the trimmer.

4. Reattach the string guide

To reattach the string guide, you will need:

• A pair of needle-nose pliers

1. Insert the string guide into the weed eater.
2. Secure the string guide with the two screws.

The screws should be tightened until they are snug, but not so tight that they damage the string guide.

Restringing a Stihl FS 57 weed eater is a simple task that can be completed in a few minutes. By following these steps, you can keep your weed eater running smoothly and efficiently.

How do I restring a Stihl FSA 57 Weed Eater?

1. Turn off the weed eater and disconnect the spark plug wire.
2. Remove the spool cover by pressing down on the tabs and sliding it off.
3. Unwind the old string from the spool.
4. Thread the new string through the eyelets on the spool, making sure that the strings are parallel to each other.
5. Wind the new string onto the spool, keeping the strings parallel and evenly spaced.
6. Trim the ends of the string so that they are equal in length.
7. Replace the spool cover.
8. Reconnect the spark plug wire.
9. Test the weed eater by running it at low speed.

What size string do I need for my Stihl FSA 57 Weed Eater?

The Stihl FSA 57 Weed Eater uses a .095-inch diameter string.

How often do I need to restring my Stihl FSA 57 Weed Eater?

The frequency with which you need to restring your Stihl FSA 57 Weed Eater will depend on how often you use it and how hard you use it. As a general rule, you should restring your weed eater every 20-30 hours of use.

What can I do if my Stihl FSA 57 Weed Eater is not stringing properly?

There are a few things you can check if your Stihl FSA 57 Weed Eater is not stringing properly. First, make sure that the string is the correct size and that it is installed correctly. Second, check the spool to make sure that it is not damaged. Third, check the tension of the string. The string should be tight enough so that it does not come off the spool easily, but not so tight that it is difficult to wind. If you have checked all of these things and your weed eater is still not stringing properly, you may need to take it to a qualified service center for repairs.

Can I restring my Stihl FSA 57 Weed Eater without removing the spool?

It is possible to restring your Stihl FSA 57 Weed Eater without removing the spool, but it is more difficult and there is a greater risk of damaging the weed eater. If you are not comfortable working on your weed eater, it is best to take it to a qualified service center for repairs.

In this blog post, we have discussed how to restring a Stihl FSA 57 weed eater. We have covered the steps in detail, with images to help you along the way. We hope that this information has been helpful, and that you are now able to successfully restring your weed eater.

Here are some key takeaways from this blog post:

• To restring a Stihl FSA 57 weed eater, you will need a new string trimmer line, a pair of pliers, and a flathead screwdriver.
• The first step is to remove the old string from the weed eater. To do this, you will need to loosen the two screws that hold the spool in place. Once the screws are loose, you can remove the spool and old string.
• The next step is to install the new string. To do this, you will need to thread the new string through the eyelets on the spool. Once the string is threaded through the eyelets, you can wind it around the spool.
• Finally, you will need to tighten the screws that hold the spool in place. Once the screws are tight, you can put the weed eater back together and start using it.

We hope that this blog post has been helpful, and that you are now able to successfully restring your Stihl FSA 57 weed eater.